Replacing a 3SGE rod bearing in-car. My 3SGE developed rod knock in rod #1, so I decided to replace the bearing with the engine in the car just to get me around for a couple of days.
Tags: Replacing a 3SGE rod bearing in-car, YouTube editor
Replacing a 3SGE rod bearing in-car
Related Videos
Crankshaft Bearing Roll-in
...
Engine Running NO OIL - NO SUMP - Seized Soild on Camera
Messing with a Mitsubishi Lancer There are loads of videos where people run an engine at full rev with no oil in it, and the engine seizes. Running it a medium rev, I wanted to see how long it would run with no lubrication, and I was surprised. Howeve...
From MrFoxman360
Rebuilding An Engine Part 1
Tips on Rebuilding a 2.2l engine out of a Mazda B2200 86-93 PLEASE STOP MENTIONING THE CHISEL AS A RING COMPRESSOR, I KNOW ITS NOT A GOOD IDEA!!! BUT I STILL HAVE FULL COMPRESSION AND IT STILL RUNS IN TIP TOP SHAPE!!! http://www.mazdatrucking.com/B2200/...
From Joseph Wilkins
TECH TALK (ep.14): Replacing the rod bearings on an e46 m3
Make sure to tune in to Tech Talks by The Little Speed Shop every Tuesday! Facebook : https://www.facebook.com/THELITTLESPE... Instagram : https://www.instagram.com/littlespeed... Twitter: https://twitter.com/littlespeedshop thelittlespeedshop.com 1770 Em...
How to test for Rod Knock using a screwdriver
Testing for rod knock and isolating the faulty cylinder using just a screwdriver and a ratchet!...
From Schrodingers Box
Crankshaft Refurbishing
Many of you have seen this one before. I apologize if bringing it back offends anyone. Domestickilla gave me a crankshaft, and it's a nice one that I want to clean up and use again. You'll be seeing a lot of it and because of this, this video deserve...
From Jafromobile
LSx How To Replace Pistons on Rod at Home DIY - 4.8 Flat Tops in a 5.3 - LS1
In this video I am pulling one piston out at at time from a 160k mile 5.3. This 5.3 will be going into my 1987 C10. I then show the removal of the dished 5.3 piston from the connecting rod and then the mount of used 4.8 flat top pistons back onto the conn...
From AGearHead4Life
03 Expedition rod knock findings/repair part 1
I bought this 03 Ford Expedition cheap from someone on craigslist that had just rebuilt the engine (replaced the block with one from an 05, reused the heads, and had new pistons/rings installed, but I don't think he honed the bores) and had what he said w...
From Toluene
How to Check Bearing Clearances Plastigage - Engine Rebuild Do It Yourself (Part One)
DIY engine rebuild. See Part Two: http://www.youtube.com/watch?v=C2aHnlHYW7A How to check main and rod bearing clearances. This is to prevent low oil pressure or seized bearings. clearance required = .001" - .003" for almost all engines I ordered t...
From EngineWelder
Integra Spun Bearing
I spun a bearing on my 1991 Acura Integra, it's best to check the oil regularly lol but it's being repaired...
From JDMG.TV
Forged 5SGTE Build | Disassembling the Cylinder Head and Refacing the Valves
i disassemble the valvetrain of my 3SGE head and reface all the valves Subscribe to follow the 5SGTE build! not sponsored by penrite Instagram: @instamadcvnt Music: Bensounds.com...
From AaronBonBarron
A Better Way to Install Rods on Pistons
http://www.horsepowermonster.com -- Installing spiral locks into a performance piston is a pain. I've found a tool that can make your life a lot easier when it comes to building performance engines. For more information, please check out http://www.horsep...